JL Audio AP 4 Channel Compact Marine Amplifier w/Bluetooth® - AP200/4BT

Name: JL Audio AP 4 Channel Compact Marine Amplifier w/Bluetooth® - AP200/4BT
Brand: JL Audio
SKU: JLA/010-03431-00
Price: 549.99 USD
Availability: InStock

SKU: JLA/010-03431-00

$549⁹⁹

Same-Day Shipping Checking cutoff…

Description

AP 4 Channel Compact Marine Amplifier with Bluetooth® - AP200/4BT

POWER THE MOMENT

With this tough and ultracompact 4-channel amplifier featuring Bluetooth® technology, you can enjoy every note from every part of your boat.

Efficient Class-D Design
Stream Audio with Bluetooth Technology
Includes Wired Remote
Ignition Protected and IP67-Rated (Excluding Cables)
Compact Build

Class-D Amplifier Technology

The highly efficient Class-D design provides lower battery drain with a higher output than Class-AB amplifiers. This delivers increased power to the connected speakers/subwoofers for an enhanced level of audio performance.

Stream On The Go

This amplifier pairs with your compatible smartphone for seamless audio streaming and includes a wired remote that can be flush-, surface-, or bar-mounted. Its compact size makes it a perfect addition to your small boat, jet ski, or overland vehicle.

Rugged Design

The included remote is IPX7-rated, and the amplifier is built to IP67 standards (excluding cables) to withstand abuse in harsh marine environments.

Specifications

Identification

MPN	010-03431-00
Barcode	729218924549

Dimensions

Dimensions (H x W x D)	1.85" x 7.28" x 4.90" (47 x 185 x 124 mm)
Weight	-

Amplifier

Amplifier Class	Class D
Channels	4

Amplifier Power

Rated Continuous (RMS) Power (14.4 V input @ 4 Ohm < 1% THD)	40 W x 4/100 W x 2 (Bridged)
Rated Continuous (RMS) Power (14.4 V input @ 2 Ohm < 1% THD)	4 Channel: 50 W x 4
Rated Continuous (RMS) Power (12.5 V input @ 4 Ohm < 1% THD)	-
Rated Continuous (RMS) Power (12.5 V input @ 2 Ohm < 1% THD)	-

Amplifier Processing

Signal-to-Noise Ratio, referred to highest rated power (A-weighted, 20 Hz-20 kHz noise bandwidth): Analog inputs	-
Signal-to-Noise Ratio, referred to 1 W (A-weighted, 20 Hz-20 kHz noise bandwidth): Analog inputs	-
Signal-to-Noise Ratio (Manufacturer Rating)	-
Damping Factor @ 4 Ω	-
Damping Factor @ 2 Ω	-
THD+N @ rated power	-
Frequency Response (+0, -1dB)	20hz - 20kHz
Input Voltage Range @ RCA Inputs	Switchable from 200 mV-2 V RMS (Low) to 800 mV-8 V RMS (High)
Input Impedance	11 kΩ (High) 20 kΩ (Low)
Remote Level Control	-
Remote Level Modes	-
Channel Input Mode Switch	-
Pass-through Preamp Output	-
Source Channel Selection for PreOuts	-

Amplifier Filters

Bass Boost EQ	None
Output Polarity Switch	-
Filter Mode(s): Channels 1 & 2	-
Filter Slope(s): Channels 1 & 2	-
Filter Frequency Range: Channels 1 & 2	-
Filter Mode(s): Channels 3 & 4	-
Filter Slope(s): Channels 3 & 4	-
Filter Frequency Range: Channels 3 & 4	-
High-Pass/Low-Pass Full Range Filter	-
HP Variable Crossover Frequency Range	-
LP Variable Crossover Frequency Range	-
Infrasonic Filter	-
Detented, Calibrated Filter Potentiometers	-

Electrical

Operating Voltage	9-16 VDC
Current Consumption (idle)	700-750mA
Current Consumption (standby)	-
Fuse Rating	35A
Recommended Fuse Type(s)	AFS, AGU, or MaxiFuse™
Minimum Copper Power/Ground Wire Gauge	4 awg Wire